With driving every day and a busy lifestyle it is easy to let the little things go a bit to long. When you are in heavy traffic and it is the worst possible time for an automotive problem that is when it is going to happen. There are a few simple automotive repairs that you can do to try to avoid problems.

A radiator flush is a easy job that most everyone can do. A properly maintained cooling system is important. It keeps the engine cool and it also helps the AC cooling system functioning properly.

Before you begin make sure that you have the proper items for the job. The radiator flush solution and proper amount of coolant. The tools you will need are a rag, screwdriver, funnel and a receptacle for catching and storing the used coolant until it can be disposed of at a proper facility.

The first thing you need to be sure of is that the engine has had plenty of time to cool down. The last thing you want is to be burned by hot coolant (very painful). Once the radiator drain or the lower radiator hose has been removed from the radiator the fluid will drain. Take the cap off to speed up the process.

Be sure that the receptacle is positioned to catch all the engine coolant. If the coolant spills over it can be messy and lead to more clean up time. Coolant can be toxic to animals and it has a sweet taste so they will drink it if you let them and it is not good for them. The answer is do not let them drink it.

When the coolant is finished draining replace the plug or the hose which ever you removed. Then add the radiator flush and fill with water. Put the cap back on the radiator and start the motor. Turn on the heater and let the engine run. The instructions usually call for 10-15 minutes. After the motor has run for the instructed time turn it off and let the motor cool down again.

After the engine is completely cool drain the flush and water into the receptacle again. Then fill the engine with the proper amount of coolant for your area. The coolant bottle should tell you what is recommended for your climate. Some severe climates call for a 50/50 mix of coolant and water. Do not use only antifreeze in your cooling system as it is very corrosive.

There are a few easy automotive repairs that you can do yourself. Just remember to always make sure the radiator and engine is completely cool. The excess fluid should always be stored in an approved container and discarded properly.

With the failing economy and the falling wages of worker, perhaps the solution to giving your car a different look will be to give your car a complete new paint job. If the mechanics and the engine of the car is in good shape, but you do not fancy the car body, then painting it will be the ideal answer.

Its a fantastic money saver, but even more so if you do it yourself as opposed to having it professionally done up in the workshop. You can do it right if you study the basics and follow the instructions for car spray painting. It’s important though if you decide you are going to take on this project that you are ready to see it complete till the end.

The supplies you need are :

-coverings to protect the unpainted regions and masking tape to hold these at the proper place -a good car wash soap and brush and also a wax/grease remover. -a few grits of sandpaper -primers and paint that is urethane base for the car spray painting -paint sprayer -safety equipment such as masks, goggles and protective clothing -knife and putty for fill-ins.

One : You must be sure that you wash the car thoroughly to remove every grime and debris. If you don’t then these things will be set in with your paint, leaving a genuinely frustrating look to the completed job. Follow up with a wax/grease remover so the paint you utilise for the car spray painting would adhere properly.

Two : Take out any rough spots by sanding. Once this has been done be certain to rinse off whatever of the loose sandings. This’s where you’ll want to utilise the putty to fill in whatsoever small pit marks, that’re have been caused from stones for example.

Three : Dont get in too much of a hurry to start your car spray painting. The car must be wholly dry so it is best to leave it to do so for a couple of hours. You can go ahead and cover whatever of the areas that your do not want to get paint on.

Four : Now you’re ready to begin with the primer. Dont skip this step, as it’ll give a much improved look to the finished project. It helps the paint to adhere the right way and allows for a more even finish. Next, once the primer is dry you’ll need to gently sand it down.

Five : Youre eventually at the step youve been waiting for. Its time to apply the color for your car spray painting. Whether you’ve selected to use aerosol paints or a spray gun, the premise remains the same. Merely apply thin coats. A couple would likely be needed. A Couple light coats are much better than one thick coat. You’ll be able to tell just by looking at the car how many more coats of paint it would need. Various would only require two whereas others will require three or 4.

Six : Eventually, down to the last step and thats applying the clear coat. This’s done precisely the same as the colored coats.

Now you can have a look at your personalized car spraying.

One thing is for sure if you are going to be a paint technician then how good you are at it will all depend on how well you learn to operate your spray guns. They are the tools of the trade and can mean the difference in your being an excellent paint technician or a poor one. Not only must one learn the various techniques involved with the spray guns there is also a must have knowledge to be gained in how to maintain the spray guns to keep them in their optimum working condition. You can have all the techniques mastered but if your gun is not operating properly then in won?t matter about your techniques.

You have to visualize what the spray gun is doing when in operation such as taking tiny droplets of paints then breaking these droplets down into thousands of small particles. What gives the spray gun its ability to do this is its nozzle set. This is the air cap, paint needle and the fluid tip. There are variables that determine the size of those thousands of droplets of paint. It will depend on the viscosity of the streams of fluid as well as how much surface tension is present. The reason you don?t get a steady stream of paint running out is because of the compressed air at the nozzle.

Getting on to the techniques of the gun when you slightly apply pressure to the trigger the air valve opens. With a little more pressure, it opens the fluid tip needle and allows the paint to flow.

If you are using a gravity gun. The amount of fluid dispersed is controlled by the viscosity of the paint. The flow is also determined by the fluid tip as well as the needle adjustment. As a rule of thumb, the gun should be almost fully open. With pressurized fluids, air pressure also affects the flow.

Equipment Set Up Knowing how to work with atomization is the key to the proper set up. The combinations of the variants must be just right. For example the exact blend of the right nozzle with the correct pressure settings combined with fluid flow and fan width all the way they are suppose to be determines the outcome. Ideally, for the standard guns try and use only enough pressure to give you the best atomization and spray pattern.

If you are new to the world of spray painting the best advice in the beginning is keep it simple. In other words, use a type of spray gun that is going to do the job you need it for. There is no need to purchase a spray gun that has a lot of additives to it if you don?t require them. On the other hand, if you are going to be using your spray gun on a regular basics then you may want something a little more advanced, as you will likely need it as you venture into your paint jobs.

When was the last time you bought your car only to realize that your neighbor has the same make or color? This doesn?t make you feel that you have had an exclusive buy, does it? You probably had a choice of some basic colors, which resulted in you picking up probably the same thing your neighbor got a day back! This is where the concept of automotive paints gained impetus.

There was a time when automotive paints were very limited as far as the shades of colors were available. Cars in the earlier days were available either in basic white or black shades. But as the demand for the colors grew, so did the experimentation of the colors begin, as far as car manufacturers were concerned. Today, the custom car painting does not mean choosing only the right shade for the 4-wheeled beauties. One has to consider factors whether the paints are rust free or scratch proof.

There are many different qualities of automotive paints available for custom car painting. Here, cost is also an important factor. For example, the poly utheranes available are generally at a higher end. There are also lower grade qualities available of this kind. This is because of a certain pigment used in them that makes it a tad expensive. The bottommost quality is the acrylic enamels. The difference between them, apart from the price factor, is the durability of the paint.

If you take a trip through any company that specializes in custom car paint jobs, you can get a variety of such paints available with their various categories and prices. Every painter has his/her own recipe for custom car painting. People have even known to change the basic look of the car or even the performance of the car (By replacing the engine) if they want a custom car as per their desire. This always adds a personal touch to the model. Once the basic body structure is changed, the custom paint job always remains to be the most important step.

The 1960s saw the use of transparent wildly colored candy apple paint applied atop a metallic coat. There was also an addition of glitter and the use of multiple coats that produced a sparkling effect. These custom car enthusiasts were also known to add decorative coats of paint in the shape of flames, pinstripes etc., over these coats. Apart from long flames on the car, automotive paint jobs also got a new twist in the story. Today, there is a growing demand for automotive logo designs. These are mainly popular amongst most car and bike enthusiasts as they can change the entire look of a plain car, to a very eye catching one.

Many people use these logos as a representation of the company or for personal use. Here, the painter has to take care that the color scheme used for the logo should match the basic color and look of the car. Most people today, love to go in for a fiery car paint color that is bold and makes a statement. These can even be seen at a longer distance. Serif fonts or delicate fonts are generally avoidable when it comes to custom car painting. This is because they may not always be visible at a distance.

If the reasons are professional and you need to display a website address, always consider the font and use contrasting colors for better readability. When it comes to automotive logo designs, one has to consider the objective of the design, the quality required and the extent to which your creativity can be unleashed. Sometimes, the designers use the various components of the car such as the handles, steering wheels etc., to display some more creative logos. Some of them break the traditional norms and implement trendy designs that can certainly look very creative and bring a ?designer? touch to the car.